Ah, considered adapter was negative but not so. Working just the pump related I get random shut down and immediate restart with connection mild keeping purple. Introducing the automation adapter to the same I7intellitouch board will shut down the commuication to the pump however, if I move that comm link for the salt generator board ports I don't get the whole pump shut down any longer. So would be the comm chip remaining flakey about the I7 board? How would be the serial ports about the salt gen ports unique from the most crucial board ports as usually there are some smaller resistors around the circuit board facts lines which i can see. May really need to up grade my intellitouch...

Follow combined with the movie beneath to discover how to install our web site as a web app on your property screen. Be aware: This attribute might not be available in a few browsers.

Just about every pool is different and every pool owner really should figure it out for by themselves. Historically, the guideline continues to be to operate the pump a minimum of one turnover every day. On the other hand, that has turned out to get a very bad indicator of true expected pump operate time. 

rjdoviak mentioned: About to check out the VS location first. Ran 3 days with the com port disconnected and no problems. Seems like a comm incompatability. What had been the identified comm concerns that you just stated? Click on to develop...

Sodium Monopersulfate should be fundamentally identical, just that has a sodium as opposed to potassium in a way that shouldn't make any variation in a very pool/tub.

Despite the fact that I do think at the end Pentair will inform you IntelliTouch is out of date and you must have the IntelliCenter upgrade kit.

To reduced CH you change from the h2o with new drinking water, with CH of . Be aware:Consumers needs to be really conscious of their CSI when their CH is at the best of bottom of your advised ranges. CYA

Then right now immediately after emptying and cleansing I refilled and applied an item with benzalkonium chloride which did not foam just as much but promptly brought up a lovely brown ring of gunk across the tub. (Photograph two). I've considering that deduced This is certainly my daughter's pretend tan. In the filter place it had been caked on.

Largely its the “tutorial” that triggers the most situation. The guidebook is edelstahl pool exactly what will make you look instantaneously tan prior to the chem essentially changes the melanin of your skin. It's going to stain outfits & mattress sheets likewise.

I haven't worked Along with the new IntelliFlo3.. But I 'Assume' that you can utilize the application or you can control with the RS-485 cable, but not both of those at the same time.. Like a check, I'd want to be sure the app is not looking to talk to the pump, when using the com cable.

Changed the board and new serial cable, exact same random shut down. Changed the push unit together with new higher board. Exact same difficulty. What is going on below as not the rest to exchange? Is there a compatability challenge Along with the more mature intellitouch i7 as Pentair denies this?

San Rafael, CA United states Jan 27, 2015 Insert bookmark #three Are you positive you weren't making use of sodium persulfate (not monopersulfate)? This isn't the same as potassium monopersulfate. The concentration is likely to become various so you should dose by distinct amounts. Sodium persulfate is often readily available in a far more pure kind although potassium monopersulfate is almost always in the triple salt so most products with it are not more than forty three% MPS.

Dec one, 2024 Include bookmark #eighteen Okay, Far more fascinating details. Fooling around with every one of the comm connections and located out this. Pump will shut down after 1 min when the data connection is dropped and lightweight goes purple to eco-friendly. Normally takes about 5 seconds to go purple on reconnection. So I disconnected all comms besides the pump and household relationship to Pentair Screenlogic with automation relationship. The Pump shut down, link gentle stayed inexperienced and pump wouldn't change back again onwith only Screenlogic and pump linked on main board. I unplugged the automation serial adapter and pump reconnected and started.

Changing your pH can even change your TA. Users must be pretty conscious in their CSI when their pH is at the top of bottom from the advised ranges.

pool holds . Should the depth may differ, use the typical depth of your pool. A superb approximation is the shallow conclude depth plus the deep conclude depth divided by two. Irregularly formed pools can be approximated by estimating the common size and width and using rectangular.